Install Guides

Z33AKE354 Adaptor Installation Guide

Included in your adaptor kit: 2x 75mm Hex Head Bolt w/ 2x 28mm Support Spacer4x 70mm Hex Head Bolt2x 45mm Hex Head Bolts8x M14 Washers (used ...

350mm Two Piece Rear Brake Upgrade Kit (Suits S/R Chassis utilising 370Z Akebono Calipers)

SKU: R34350AKE-K *If you are uncertain about any part of this kit’s installation, please reach out to us or a trusted, professional and competent person. Helpful ...

354mm Adaptor Bracket Installation Guide (R34 GTT, R33 GTST)

Special Notes: In an attempt to create a lightweight rotor and considering the outer ring is the heaviest component, we’ve enlarged the aluminium centre hat as ...

340mm Rear Rotor Caliper Adaptor (Suits: S/R Chassis utilising 350Z Brembo Calipers)

324mm Adaptor Bracket Installation Guide (R34 GTT)

To begin, determine the left and right-hand side adapters. They are marked as follows: R34324-R or R34324-L In the bolt kit, you will have:2x M14 x 1.5 ...

Wilwood Brake Pad Guide

Once the brake system has been tested and determined safe to operate the vehicle, follow these steps for the bedding of all new pad materials and ...

Semi-Rigid Aluminium SubFrame Spacers

Each spacer is labelled with its position on the subframe. You should have: 4x Bottom 2x Front Up 2x Rear Up You will need to remove ...

324mm Rotor Caliper Adapters (R33 GTS-T Caliper)

To begin, determine the left and right-hand side adapters. They are marked as follows:324R33_L or 324R33_R Remove your original Rotor and Caliper and then remove the ...

326mm Front Brake Package (Subaru BRZ ZC6, Toyota 86 ZN6)

Please see the below video on how to install this brake kit. NOTE:If you have a Subaru BRZ 2022 model with Aluminium knuckles, you will need ...

install guide featured image bmc stopper

Brake Master Cylinder Stopper (Subaru BRZ ZC6, Toyota 86 ZN6)

Attached the knurled spacer using the M8x35mm bolt with an M8 lock nut to the HFM.Parts Brake Master Cylinder (BMC) Stopper. Remove the grommets in the ...

354mm Front Two Piece Brake Upgrade Kit (R33 GTR)

Check out our installation video below for step-by-step instructions, hints, tips, and tricks to achieve a perfect install. Please Note: There is an error in this ...

340mm Rotor Caliper Adapter

Remove the Caliper and rotor from their original position. You may need to peel back or remove the outer edges of the backing plate.Make sure to ...

install guide featured image 337 adaptor

337mm Rotor Caliper Adaptor

Remove Caliper and rotor from the original position. You may need to peel back or remove the outer edges of the backing plate. Make sure to ...

324mm Rotor Caliper Adaptor Bracket (WIL-NISS324)

This kit is for use with Wilwood Caliper P/N 120-11573. Remove your existing caliper, rotor and brake line. You will also need to remove the backing ...

324mm Rotor Caliper Adaptors (S13, S14, S15, R32 GTS-T)

Remove Caliper and rotor from the original position. You may need to peel back or remove the outer edges of the backing plate. Make sure to ...

install guide featured image 316mm adaptor

316mm Rear Brake Package

Important! Before fitting the brake line, there are 2x male/female stainless fittings that need to be fit to the Wilwood Caliper. These should be installed using ...

install guide featured image 300mm adaptors

300mm Rotor Caliper Adaptors

Remove Caliper and Rotor from their original position. Remove the backing plate or slice back the outer edges to fit the large 300mm Rotors. Be sure ...

Big Bore Clutch Slave Cylinder

1. Test FitHold the clutch slave against the bell housing prior to fitment/bolting on. This is so that you can check that there is enough clearance ...