Spend $250+ for Free Shipping
Fit it now, Pay it later
Fast Shipping Worldwide
Spend $250+ for Free Shipping
Fit it now, Pay it later
Fast Shipping Worldwide

Suits Nissan Skyline, Silvia, Z32 (ABS + Non ABS)

BM57 Brake Master Cylinder RHD

$ 189.00

Spend $250+ for Free Shipping
Free Australia Wide Postage on Order $250+
Pickup Available
South Kingsville, VIC 3015 | Ready in 1-2 Hours | Mon - Fri 10am to 4pm
Lifetime Warranty
All HFM.Parts Cylinders come with a lifetime warranty*
In Stock

BM57 Reservoir Relocation Kit

Max Available:



HFM.Parts have re-developed their superseded Brake Master Cylinder with higher quality rubbers and internals, with a classic monochrome design. With a whopping 17/16 Inch (27mm) piston bore size, this is the perfect application if you are looking to increase your braking performance and reduce that spongy feeling to give you a firmer brake pedal with less travel. HFM.Parts have included a Tapered Grub Screw so that this model can be applied to both ABS and NON-ABS vehicles.

The dark colour of HFM.Parts Brake Masters come from their Geomet® coating. As well as providing some heat protection and environmental resistance, this coating is environmentally friendly as it contains no Chromium, the leftover solution is recycled and no chemicals are evaporated.


Split Point = 35kgf  (498psi) x 0.4

TIP! – Soften your pedal feel by increasing the brake booster size.


Nissan 180SX SR20
Nissan Silvia S13 SR20
Nissan Silvia/200SX S14
Nissan Silvia/200SX S15
Nissan Skyline R32 GTR
Nissan Skyline R32 GTS-T
Nissan Skyline R33 GTR
Nissan Skyline R33 GTS-T
Nissan Skyline R34 GTT
Nissan 300ZX Z32

  • The product is suited for RHD models only.
  • If your car has ABS brakes, you need to block either the middle port or the rear port closest to the booster using the provided tapered grub screw. The ports are the same but split in two.
  • 4-Piston Calipers are required due to the increase in fluid volume.

In the Box

1x BM57 Brake Master Cylinder
1x Tapered Grub Screw

Install Video


Q. Will this fit my vehicle? A. We have only confirmed fitment for the vehicles mentioned under compatibility. If your vehicle is not listed, then we don't know if it fits. Q. My brake lines feed from the top, can I still use this Brake Master? A. Yes. Although the HFM.Parts Brake Master is designed with side ports, most brake lines can be massaged around until they reach the brake master’s ports. Q. My brake lines feed from the bottom, can I still use this Brake Master? A. Yes. Although the HFM.Parts Brake Master is designed with side ports, most brake lines can be massaged around until they reach the brake master’s ports. Q. The fluid sensor connector is on the wrong side, what can I do? A. You can easily swap the sensor connector to either side of the HFM.Parts Brake Master by following these steps. On the terminal side, push a small flat screwdriver in between the sensor connector and the bottom of the reservoir to lightly pry apart the lock tab. On the opposite side of the sensor connector, push through to pop it out. *This is much easier to do prior to installation! Q. I have a round (or other shape) fluid sensor connector, will it fit? A. No, our fluid sensor connector is rectangle (as shown in the product photo), in order to plug your existing fluid sensor connector into our one, you will need to cut your existing connector off and join the two exposed wires to individual spade terminals. Then, you can push these onto our connector. Q. Will the proportioning valve suit my car? A. The Sepcs for the HFM.Parts BM57 are “Split Point = 35kgf  (498psi) x 0.4” which can suit the models listed depending on the vehicles brake and suspension set up, your brake bias may differ. Q. How will I know if this BM57 will suit my car? A. Racing is all about optimising for performance, unfortunately, the only reliable way is to test suitability on a racetrack. Q. I’ve done an engine swap on my car, can I relocate the reservoir of this brake master? A. Yes! We have created a relocation kit for this exact reason! Just above the “add to cart” button, you should see an option to add a reservoir relocation kit. This is particularly handy for customising your engine bay to suit your needs.

Install Guides


Modifying vehicles is a specialist task and requires the knowledge and experience of competent individuals to be conducted safely.
We recommend this product be installed by a competent person. Instructions are given with every order where available, however, If you would like a copy prior to ordering, you're welcome to contact us: Go to Contact Page

Customer Photos
We're yet to upload our customers photos.
Want to be featured here? Send in your best shots: sales@hfm.parts

4.84 Stars
Customer Reviews
37 reviews
    The item fitted and the brakes work...
    Very quick and efficient international parts supply
    Ben Gainfort
    Experience is great, bench bleeding was no problem
    wesley paolino
    Recieved on time. Good quality product.
    Excellent service! Super Fast shipping!!!
    The master cylinder was good and seems to have worked well so far (only bled brakes, no test drive yet) and was the only place I could find a RHD non-ABS BM57. However the pins on the connector for the brake level sensor were out of alignment slightly so I had to use the connector from my old MC.
    John Grasty
    This is the first upgrade i do to any car and has been for years. Thank you HFM keep up the good work.
    Pro Fab Exhaust
    The part was a good fit and works well. Excellent company to deal with. Thankyou. I
    alan S.
    Product was delivered on time and what i wanted Thank you
    Alix T.
    Fits well and good quality. Extra speedy delivery.
    Greg C.
    Great part. Got stickers. Next day delivery. Amazing company
    Rashad M.
    Exactly the part I needed
    Jacob L.
    Great quality item which was the exact measurements stated. Had to use this master cylinder to fit with the SR20DET engine.
    Philip M.
    It’s near impossible to find a non ABS BM57. HFM has hit it out of the park with quick shipping and great price!
    Lance M.
    the front allen screw are not tight & sensor connector to be on the right not left.
    Yoon S.
    Good item. Would be better if you offer the BM50 switch to BM57 switch
    Aaron L.
    Service was great and the new master cylinder works perfectly on our big brake upgrade:-) Cheers
    Brett O.
    Have only test fitted and fits perfectly
    Michael C.
    Good seller...great product
    Michael p.
Leave a Review
Leave a review