324mm Wilwood Front Brake Kit for 350Z & V35
Suits: Nissan 350Z Z33, Skyline V35, with or without factory Brembo calipers (17" wheels minimum)
New Wilwood calipers, 324mm two-piece rotors and everything to bolt them on. Built for the 350Z and V35.
- Wilwood Forged Superlite 120-11133 4-piston calipers (pair)
- 324mm two-piece rotors, arrive assembled, runout tested and balanced
- Adaptor brackets, braided lines, fittings and pads included
- Needs 17″ wheels or larger
$2,253.00 AUD
Inclusions
-
324mm Front Two Piece Rotors
In stock
HFM-ROT-324-350
$749.00 AUD
-
324mm Wilwood Caliper Adaptor Brackets for 350Z & V35
In stock
WIL-Z33324
$209.00 AUD
-
Front Braided Brake Lines for 350Z & V35
In stock
Z33X-BRKE-F
$219.00 AUD
-
Wilwood Caliper Inlet Fitting, NPT to M10 × 2 (Pair)
In stock
WF1/8-M10
$36.00
Requirements
Why upgrade
Non-Brembo 350Z and V35 cars go from the factory 296mm front rotor to 324mm, with 4-piston Wilwood calipers. Brembo cars get a new caliper option, which may be easier to find or more affordable than a factory Brembo. You get new calipers, rotors, brackets, lines and pads in one box.
What’s in the kit
- 324mm two-piece front rotors (pair)
- Wilwood Forged Superlite 120-11133 calipers (pair)
- 324mm caliper adaptor brackets (pair) with bolt kit
- Front braided brake lines for 350Z and V35 (pair)
- 2 x Wilwood caliper conversion fittings
- Wilwood front brake pads: BP10 for street, or BP20 for street and track
The calipers
The Forged Superlite internal caliper uses internal fluid ports, so there are no external crossover tubes to damage. Wilwood calipers run without dust boots. Here’s why.
The caliper inlet is 1/8-27 NPT. The included conversion fittings change it to metric, so our braided lines connect straight up.
The rotors
A two-piece rotor splits the braking ring from the hat. The hat is heat-treated T6-6061 aluminium and each rotor weighs 7.3kg. The ring is free to expand and contract as it heats and cools. When the rings wear, keep the hats and fit replacement rotor rings.
Two-piece rotors arrive with the hat and ring already bolted together, runout tested and balanced as an assembly. Always check the hat bolts are at 13–15 ft-lb before fitting, as you would with any two-piece rotor. Otherwise, it’s a direct bolt-on.
Will it fit my car?
The kit suits the Nissan 350Z Z33 and Skyline V35, with or without factory Brembo calipers. You need 17″ wheels or larger. Factory brake lines do not suit this setup, so longer braided lines are included.
Specifications
| Upgrade | 296mm to 324mm front rotors (non-Brembo cars) |
|---|---|
| Rotors | HFM.Parts 324mm two-piece, 7.3kg per rotor |
| Rotor thickness | 30mm (28mm minimum) |
| Rotor height | 49mm |
| Centre bore | 68mm |
| Hat bolt torque | 13–15 ft-lb |
| Calipers | Wilwood Forged Superlite 120-11133, 4-piston (pair) |
| Caliper inlet | 1/8-27 NPT, metric conversion fittings included |
| Adaptor brackets | T6-6061 billet aluminium, hard anodised, stainless steel Heli-Coils |
| Brake lines | HFM.Parts front braided lines, made in Melbourne |
| Pads | Wilwood BP10 or BP20 |
| Wheel size | 17″ minimum |
| Position | Front |
Fitting
Clean the hub face of dirt and rust before fitting the rotors. The brackets are marked L and R and fit to the outside of the knuckle. Torque the bracket bolts to 58–62 ft-lb and the caliper bolts to 50–59 ft-lb. Test fit each caliper to its bracket. If any casting material on the caliper meets the bracket, linish it back until the bolt holes line up. Fit the conversion fittings with thread sealant.
Full steps are in the 324mm front brake kit install guide.
We recommend installation by a licensed mechanic.
Pairs with
Every part of this kit is also sold on its own:
- 324mm two-piece front rotors for 350Z and V35
- 324mm caliper adaptor brackets for Wilwood Superlite, 350Z and V35
- Front braided brake lines for 350Z and V35
- Wilwood Forged Superlite caliper 120-11133 (pair)
- Wilwood caliper conversion brake fitting
- Wilwood front brake pads for 120-11133
- Replacement two-piece rotor rings (324mm 350Z, V35)
- Uses Wilwood Superlite Caliper
- Increase Rotor Size by up to 28mm
- High-Quality Billet Adaptor
What's Included
-
2× HFM.Parts 324mm two-piece front rotor (hat and ring assembled)
-
2× Wilwood Forged Superlite 120-11133 caliper
-
2× HFM.Parts 324mm caliper adaptor bracket (left and right)
-
1× Bolt kit for the adaptor brackets and calipers
-
1× HFM.Parts front braided brake lines (pair)
-
2× Wilwood caliper conversion fitting
-
1× Wilwood front brake pads, BP10 or BP20 (as selected)
Customer Installs
Installs of this part — and similar parts in this category.
Will it fit your car?
Find your car in the list below and add it to your garage. Every part page then checks it for you.
Our Story
We weren't always HFM.Parts; we were Holford Motors. Our brand's identity was forged not in an office, but on the local circuits in the high-stress world of competitive drifting. Our ultimate testbed was our Nissan S14 Drift car, driven by champion Luke Fink. Pushing that car to its limits exposed a crucial truth: achieving genuine, repeatable performance meant relying on components that simply weren't available affordably on the market.
The HFM.Parts brand was born
We made the commitment to design and manufacture the uncompromising, high-quality performance parts that we, as competitive racers, demanded ourselves. Every component you see is a solution conceived, tested, and proven by us. When you choose HFM.Parts, you are investing in components engineered by racers, for racers, ensuring your vehicle delivers its maximum performance potential.
Modifying vehicles is a specialist task and requires the knowledge and experience of competent
individuals to
be conducted safely.
We recommend this product be installed by a competent person. Instructions are given with every
order
where
available, however, If you would like a copy prior to ordering, you're welcome to contact us
Based on 27 verified reviews