354mm Akebono Caliper Adaptor Brackets for R34 GTT
Suits: Nissan Skyline R34 GTT with 370Z Z34 front Akebono calipers and 354mm rotors (minimum 18" wheels)
Run 370Z Akebono calipers and 354mm rotors on your R34 GTT. A bolt-on bracket for a bigger front brake.
- Steps up from 310mm to 354mm front rotors
- T6-6061 billet aluminium, hard anodised
- Fitted with stainless steel Heli-Coils
- Full bolt kit and support spacers included
$239.00 AUD
Requirements
Why upgrade
These brackets let you fit factory 370Z front Akebono calipers and 354mm rotors to the R34 GTT, up from the factory 310mm rotors. They’re machined from T6-6061 billet aluminium, hard anodised, and fitted with stainless steel Heli-Coils so the threads hold up over time.
Will it fit my car?
Built for the Nissan Skyline R34 GTT. You’ll also need:
- HFM.Parts 354mm front two-piece rotors (Z3544932) or an OEM 370Z equivalent
- A pair of 370Z Z34 front Akebono calipers
- 18″ wheels or larger
The factory brake lines sit at full extension with these brackets, so we recommend our front hard line delete braided brake lines. Want everything in one go? Grab the 354mm front brake kit for R34 GTT.
Specifications
| Upgrade | 310mm to 354mm front rotors |
|---|---|
| Bracket material | T6-6061 billet aluminium, hard anodised |
| Thread inserts | Stainless steel Heli-Coils |
| Rotors | HFM.Parts 354mm two-piece (Z3544932) or OEM 370Z equivalent |
| Calipers | 370Z Z34 front Akebono |
| Wheel size | 18″ minimum |
| Bolt torque | 58–62 ft-lb |
| Position | Front |
| Sold as | Pair (left and right) |
Fitting
Clean any rust off the hub face before fitting the rotor. Use Loctite 262 or equivalent on all bolts and torque the adaptor and caliper bolts to 58–62 ft-lb. Check the rotor clears the backing plate and bend the plate away if needed. Full steps are in the 354mm adaptor bracket install guide for R34 GTT.
We recommend installation by a licensed mechanic.
Pairs with
- Solid Billet Aluminium
- Designed and Tested In-House
- Stainless-Steel Heli-Coils
What's Included
-
2× Caliper adaptor bracket (left and right)
-
2× 75mm hex bolt with 28mm support spacer
-
2× 50mm hex bolt with 10mm support spacer
-
4× 60mm hex bolt
-
8× M14 washer
Customer Installs
Installs of this part — and similar parts in this category.
Will it fit your car?
Find your car in the list below and add it to your garage. Every part page then checks it for you.
Our Story
We weren't always HFM.Parts; we were Holford Motors. Our brand's identity was forged not in an office, but on the local circuits in the high-stress world of competitive drifting. Our ultimate testbed was our Nissan S14 Drift car, driven by champion Luke Fink. Pushing that car to its limits exposed a crucial truth: achieving genuine, repeatable performance meant relying on components that simply weren't available affordably on the market.
The HFM.Parts brand was born
We made the commitment to design and manufacture the uncompromising, high-quality performance parts that we, as competitive racers, demanded ourselves. Every component you see is a solution conceived, tested, and proven by us. When you choose HFM.Parts, you are investing in components engineered by racers, for racers, ensuring your vehicle delivers its maximum performance potential.
Modifying vehicles is a specialist task and requires the knowledge and experience of competent
individuals to
be conducted safely.
We recommend this product be installed by a competent person. Instructions are given with every
order
where
available, however, If you would like a copy prior to ordering, you're welcome to contact us
Be the first to review this product. Here's what other customers have been saying about our range:
Recently purchased this item? If you could take a moment to leave us a review, that would be awesome!