Spend $250+ for Free Shipping
Fit it now, Pay it later
Fast Shipping Worldwide
Spend $250+ for Free Shipping
Fit it now, Pay it later
Fast Shipping Worldwide

Suits Nissan Skyline, Silvia, Z32

BM57 Brake Master Cylinder (Rebuild Kit)

$ 69.00

Spend $250+ for Free Shipping
Free Australia Wide Postage on Order $250+
Pickup Available
South Kingsville, VIC 3015 | Ready in 1-2 Hours | Mon - Fri 10am to 4pm
In Stock
Max Available:

Description

HFM.Parts have re-developed their superseded Brake Master Cylinder with higher quality rubbers and internals with a classic monochrome design. If you have an old/worn out OEM Nissan or HFM.Parts BM57 BMC kicking around that has lost brake pedal pressure and you cannot get seals for it, the HFM.Parts Rebuild Kit with full piston seal kit and reservoir might be what you need.
To purchase a complete HFM.Parts BM57 Brake Master Cylinder click here.

Compatibility

Fitment:
Nissan 180SX SR20
Nissan Silvia S13 SR20
Nissan Silvia/200SX S14
Nissan Silvia/200SX S15
Nissan Skyline R32 GTS-T
Nissan Skyline R33 GTS-T
Nissan Skyline R34 GTR
Nissan Skyline R34 GTT
Nissan 300ZX Z32

Requirements:

Suits: 26.5mm – 17/16″ Bore
For R34 GTR – Please refer to FAQ regarding “retaining lock screw”.

 


In the Box

1x Reservoir
2x Reservoir Grommets
1x First piston with rubber cup
1x Second piston with rubber cup
1x Piston Lock Ring

FAQs

Q. Will this fit my vehicle? A. We have only confirmed fitment for the vehicles mentioned under compatibility. If your vehicle is not listed, then we don't know if it fits. Q. Does my brake master cylinder need to be honed even if it looks ok? A. Yes! It may look smooth to the human eye but the bore could still be out of round and worn. It will require honing for the new piston seals to seal correctly. Q. The fluid sensor connector is on the wrong side, what can I do? A. You can easily swap the sensor connector to either side of the BM57 by following these steps. On the terminal side, push a small flat screwdriver in between the sensor connector and the bottom of the reservoir to lightly pry apart the lock tab. On the opposite side of the sensor connector, push through to pop it out. *This is much easier to do prior to installation! Q. I have a round (or other shape) fluid sensor connector, will it fit? A. No, our fluid sensor connector is rectangle (as shown in the product photo), in order to plug your existing fluid sensor connector into our one, you will need to cut your existing connector off and join the two exposed wires to individual spade terminals. Then, you can push these onto our connector. Q. My OEM pistons have an elongated slot which is different to what will be supplied? Why is this? A. Some brake masters utilise a retaining screw (circled in red) to hold the pistons in place. Our pistons do not require this mechanism. If your Brake Master has a retaining lock screw, you will need to either shorten or replace it with a shorter screw to block the fluid from leaking.

Install Guides

Disclaimer

Modifying vehicles is a specialist task and requires the knowledge and experience of competent individuals to be conducted safely.
We recommend this product be installed by a competent person. Instructions are given with every order where available, however, If you would like a copy prior to ordering, you're welcome to contact us: Go to Contact Page


Customer Photos
We're yet to upload our customers photos.
Want to be featured here? Send in your best shots: sales@hfm.parts

5 Stars
Customer Reviews
3 reviews
    The kit was easy to install and has made a unusable master cylinder epic again. I would highly recommend.
    Anonymous
    Good delivery time
    Waynne Wale
    Very professional and quick
    Ronnie Beard
Leave a Review
Leave a review

Search